Main Menu
Your Cart

Naraku Secondary Slider (DIO, GET, QMB)

Naraku Secondary Slider (DIO, GET, QMB)
Naraku Secondary Slider (DIO, GET, QMB)
Naraku Secondary Slider (DIO, GET, QMB)
Naraku Secondary Slider (DIO, GET, QMB)
Naraku Secondary Slider (DIO, GET, QMB)
Naraku Secondary Slider (DIO, GET, QMB)

Description: Naraku Secondary Slider aka Torque Driver with 2 different linear guide slots for 139QMB 49cc-50cc 4-stroke GY6 50 engine based scooters, ATVs, and off-road karts. Also, fit Honda Dio/Elite and Honda GET only with conversion secondary pulley assembly.

Most torque drivers have curved slots which is not ideal for performance gains but fine for rideability. The 2 different linear options mean you can give more emphasis to acceleration. This is more a feature for the race track but can give the everyday commuter improved drive with no loss of performance at the rear wheel.

Compatible with sport clutches on the market works on Honda Dio AF16 AF18E 50; Elite S/SE/SR 1994-2001, Daelim Cordi 50, Kymco Fever/ZX50, SYM DD50, GY6 40QMB 50cc 2-stroke, 139QMB 49cc-50cc 4-stroke, 50QMF 90cc-100cc, GY6 139QMB 49cc-50cc engines, Buddy50, Filly 50, Kymco, QLink, Peugeot, Piaggio, RoughHouse, SYM, TaoTao, Metropolitan GET 2012 & older, Honda Ruckus GET all U.S. Model, and virtually any scooter engine with these measurements.

Installation: Make sure variator drive face is seated properly and not get its teeth chewed by the Bendix: 1. Slack the belt by opening the CVT clutch gives belt slack to the variator side. 2. Then install the variator drive face while lifting the slack belt further away from the center boss if done properly should not see any splines between variator drive face slop-side and boss flat-side. Should be flushed together. 3. Then install the existing variator fan, washer, and hand-tight nut. 4. Finally, apply blue Loctitetorque nut to 30-35ft lbs. For reassurance please consult your manufacturer variator torque specs.

NOTE: This Naraku Secondary Slider/Pulley measures 33.5mm I.D. Please verify before ordering. This Naraku Secondary Slider/Pulley is for the Honda Dio AF16 AF18E 50; Elite S/SE/SR 1994-2001, Daelim Cordi 50, Kymco Fever/ZX50, SYM DD50, GY6 40QMB 50cc 2-stroke, 139QMB 49cc-50cc 4-stroke engines. Will work on Metropolitan GET 2012 & older, Honda Ruckus GET all U.S. Model ONLY if you use WITH upgrade NCY Pulley Shaft, will NOT work with OEM pulley shaft.

Specifications:

Includes the following Secondary slider (torque driver) and O-rings.

•    Secondary Slider Funnel ID: 33.5mm / OD: 43.10mm / H: 47mm
•    Secondary Slider Plate OD: 118mm
•    Made in Taiwan
•    Fit Belt Size: 654 (Fit DIO ONLY)
•    Fit Belt Size: 660785 (Fit GET ONLY)
•    Fit Belt Size: 669, 729, 788 (Fit QMB ONLY)
•    Fit Compression Spring: 1k1.5k2k rpm
•    Fit Dowel Pin Set (8x14mm)
•    Fit DIO 49/90cc+
•    Fit GET 49/50cc
•    Fit QMB 49/50cc+

Supported Models: Naraku CVT Kit (Part# KIT.A.139QMB); Honda Dio AF16 AF18E 50; Elite S/SE/SR 1994-2001, Daelim Cordi 50, Kymco Fever/ZX50, SYM DD50, GY6 40QMB 50cc 2-stroke, 139QMB 49cc-50cc 4-stroke, 50QMF 90cc-100cc, GY6 139QMB 49cc-50cc engines, Buddy50, Filly 50, Kymco, QLink, Peugeot, Piaggio, RoughHouse, SYM, TaoTao, Metropolitan GET 2012 & older, Honda Ruckus GET all U.S. Model, and virtually any scooter engine with these measurements.

-----
Item Weight & Product Dimensions:
•    0.6 pounds | 4.464" (OD) x 1.181" (ID) x 1.85" (H)

Sorry, this video is NOT dubbed in English. Khmer speaking only.

Write a review

Note: HTML is not translated!
Bad Good
Captcha
Naraku Secondary Slider (DIO, GET, QMB)
  • Stock: 20
  • Reward Points: 2
  • Part #: NK900.53
Sold: 5
Views: 9785
$69.95
Price in reward points: 70

Included