Main Menu
Your Cart

NCY Variator Ramp Top (DIO, QMB)

NCY Variator Ramp Top (DIO, QMB)
NCY Variator Ramp Top (DIO, QMB)
NCY Variator Ramp Top (DIO, QMB)
NCY Variator Ramp Top (DIO, QMB)

Description: NCY Variator Ramp Top aka variator pressure plate for your 139QMB and DIO. NCY Variator Housing (sold separately, see Part# 1200-1050).

May also, compatible with most variator housing on the market works on Honda Dio AF16 AF18E 50; Elite S/SE/SR 1994-2001, Daelim Cordi 50, Kymco Fever/ZX50, SYM DD50, GY6 40QMB 50cc 2-stroke, 139QMB 49cc-50cc 4-stroke, 50QMF 90cc-100cc, GY6 139QMB 49cc-50cc engines, Buddy50, Filly 50, Kymco, QLink, Peugeot, Piaggio, RoughHouse, SYM, TaoTao, and virtually any scooter engine with these measurements.

NOTE: Recommend using a new belt with this kit. Belt and the belt drive-facing plates KEEP DRY. All, other areas apply moly-graphite grease when assembling. For Honda DIO require belt-size 654-18-30 (Part# BD44DIO-6541830).

Installation: Make sure variator drive face is seated properly and not get its teeth chewed by the Bendix: 1. Slack the belt by opening the CVT clutch gives belt slack to the variator side. 2. Then install the variator drive face while lifting the slack belt further away from the center boss if done properly should not see any splines between variator drive face slop-side and boss flat-side. Should be flushed together. 3. Then install the existing variator fan, washer, and hand-tight nut. 4. Finally, apply blue Loctitetorque nut to 30-35ft-lbs. For reassurance please consult your manufacturer's variator torque specs.

Specifications:

Include the following Variator top only.

•    1x Metal Top ID: 14.15mm / OD: 73.50mm / H: 11.58mm
•    Made in Taiwan
    Fit Starter: Bendix / Lock: Bracket
•    Fit Variator Housing: 88mm89mm Weights: 16x13mm / Slides: 3 Boss: 20mm / Shims: 20mm
    Fit Variator Shaft Nut: M12 / Washer: M12 / Socket: 17mm
•    Fit Belt Size: 669729, 788-18-30 (Fit QMB ONLY)
•    Fit Belt Size: 654669-18-30 (Fit DIO ONLY)
•    Fit Dowel Pin Set (8x10mm)
•    Fit DIO 49/90cc+
•    Fit QMB 49/50cc+

Supported Models: NCY CVT Kit (Part# 1200-1171); Honda Dio AF16 AF18E 50; Elite S/SE/SR 1994-2001, Daelim Cordi 50, Kymco Fever/ZX50, SYM DD50, GY6 40QMB 50cc 2-stroke, 139QMB 49cc-50cc 4-stroke, 50QMF 90cc-100cc, GY6 139QMB 49cc-50cc engines, Buddy50, Filly 50, Kymco, QLink, Peugeot, Piaggio, RoughHouse, SYM, TaoTao, and virtually any scooter engine with these measurements.

-----
Item Weight & Product Dimensions:
•    0.156 pounds | 2.894" (OD) x 0.703" (ID) x 0.456" (H)

Write a review

Note: HTML is not translated!
Bad Good
Captcha
NCY Variator Ramp Top (DIO, QMB)
  • Stock: 38
  • Part #: 1200-1056
Sold: 6
Views: 14055
$12.95
Price in reward points: 13

Included