Naraku CVT KIT (Aprilia, JOG, Zuma 50)
Description: Naraku CVT KIT aka Super CVT transmission kit for 40QMB 2-stroke engines. Complete transmission kit of Naraku components, all tuned to another. Since Chinese-built scooters are not kitted with top-end components out of the factory, this is the easiest way to overhaul the transmission without expert help. This negates any restrictions. Top speed and drivability on hills are improved, meaning higher top end and better acceleration! Kit contains variator, variator sleeves, belt, belt pulley, clutch, and clutch bell. Suitable for all 2-stroke scooters with 1E40QMB and 1PE40QMB engines with a 16mm crankshaft and a belt length of 788mm. Kit for scooters in untuned condition. Where changes are made to exhaust or cylinder, the variator must also be adapted and, where necessary, a stronger counter pressure spring fitted.
NOTE: Recommend using a new belt with this kit. Belt and the belt drive-facing plates KEEP DRY. All, other areas apply moly-graphite grease when assembling. Example, lubricate slider grooves, slider pins, ball bearing seat, and inner funnel area with heat-resistant moly-graphite grease.
Installation: 1. Slack the belt by opening the CVT clutch gives belt slack to the variator side. 2. Then install the variator drive face while lifting the slack belt further away from the center boss if done properly should not see any splines between variator drive face slop-side and boss flat-side. Should be flushed together. 3. Then install the existing variator fan, washer, and hand-tight nut. 4. Finally, apply blue Loctite, torque nut to 30-35ft-lbs. For reassurance please consult your manufacturer's variator torque specs.
Specifications:
Naraku CVT KIT (Aprilia, JOG, Zuma 50) – OPTIONAL ADD-ON (IN RED).
Includes the following Variator, Variator boss, Variator drive face, Belt, Clutch, and Clutch bell.
1. Include Naraku Drive Face Fan Drive Face.
• 1x Aluminum Drive Face Fan Weight: 96.4gm
• Splines: 15 / ID: 14<16mm / OD: 93.7mm / H: 20mm
2. Includes Naraku Variator 95mm Coated Gray, Roller weights, Variator boss, Variator housing, Variator slides, and Variator top.
• 1x Alumin-Alloy Housing ID: 21mm / OD: 95mm / H: 26.5mm / W: 187.1gm
• 1x Stainless Steel Boss L: 36.5mm / ID: 16mm / OD: 20.9mm / W: 39.7gm
• 1x Metal Top Splines: 15 / ID: 14.7<16.3mm / OD: 79.3mm / H: 14.6mm / W: 90.7gm
• 6x Roller Weights (white): 15x12 5gm
• 6x Roller Weights (white): 15x12 5.5gm
• 6x Roller Weights (white): 15x12 6gm
• 3x Plastic Slides (red) L: 19.11mm / W: 14.8mm / H: 6.7mm
3. Includes Naraku 110mm Clutch Performance Sport Clutch housing, Clutch springs, and Clutch weights.
• 1x Clutch ID: 24.3<28mm / OD: 107mm / H: 27mm / W: 720gm
• 3x Clutch Spring (red): 2000 RPM
• 3x Clutch Weights
4. Include Naraku Clutch Bell, Clutch Bell PTFE Coated.
• 1x Iron Clutch Bell Vented ID: 112mm / OD: 123.3mm / H: 32mm / W: 533gm
• Splines: 16 / ID: 11<12mm / OD: 18mm / H: 15.4mm
5. Include Naraku CVT Drive Belt
• Length: 788mm (Loop 15.511 in.) / W: 113.4gm
• Top Width: 17mm (0.669 in.)
• Groove Angle: 30º
• Made in Taiwan
• Fit Clutch Sheave: 33mm / Bearing Funnel: 42mm / Nut: M28 / Socket: 39mm
• Fit Variator Shims: 18mm
• Fit Belt Size: 788-17-30 (Fit JOG ONLY)
• Fit Belt Size: 748-18-28 (Fit Zuma ONLY)
• Fit Belt Size: 818-19-28 (Fit Aprilia ONLY)
• Fit Compression Spring: 1k, 1.5k, 2k rpm
• Fit Clutch Springs: 1k, 1.5k, 2k rpm
• Fit Aprilia 50
• Fit JOG 50
• Fit Zuma 50
Supported Models: NCY CVT KIT (Part# 1200-1197); Yamaha C3, Yamaha Zuma CW50, Yamaha Zuma 50F, Yamaha Vino Minarelli Jog engines, Chinese Yamaha Clones 1PE40QMB 1E40QMB engines, Malaguti, CPI, Aprilia Scooters with Piaggio engines, and Franco-Morini 50cc engines found in the 1E41QMB Suzuki AD50 AG50, TGB R50X, TGB 101, TGB 303, and Peirspeed Scooters.
-----
Item Weight & Package Dimensions:
• 4.138 pounds | 12.5” (L) x 8.75” (W) x 4.5” (H)