Main Menu
Your Cart

Naraku Drive Face HS-CNC V.2 (139QMB)

Naraku Drive Face HS-CNC V.2 (139QMB)
Naraku Drive Face HS-CNC V.2 (139QMB)
Naraku Drive Face HS-CNC V.2 (139QMB)
Naraku Drive Face HS-CNC V.2 (139QMB)
Naraku Drive Face HS-CNC V.2 (139QMB)
Naraku Drive Face HS-CNC V.2 (139QMB)
Naraku Drive Face HS-CNC V.2 (139QMB)
Naraku Drive Face HS-CNC V.2 (139QMB)
Naraku Drive Face HS-CNC V.2 (139QMB)
Naraku Drive Face HS-CNC V.2 (139QMB)

Description: Naraku Drive Face HS-CNC V.2 for 139QMB 49cc-50cc scooter engines. V.2 is the latest version of the CNC-machined drive face pulley from Naraku. This enhanced version now allows you to mount the original variator fan overlay and kickstart star him (See Fig. 3), the edge angle was revised again and combines a little more top speed with sufficient power. The CNC-machined running surface of the disc allows for a clean, low-vibration belt operation. Unlike CNC machined drive face pulley for other types of engines, the HS-CNC has teeth that perfectly aligned with the electric starter bendix. This can be reused, saving tedious "clicking" waste and wear. The perfect aligned teeth do however make the Naraku Drive Face most performance driven in addition to its flashy red-race color.

NOTE: The variator fan overlay and kickstart star him (see Fig. 3) are not included only for donor placement demo. If required, please order separately. Recommendations: Use a new belt with this kit and graphite or moly grease when assembling.

Installation: Make sure variator drive face is seated properly and not get its teeth chewed by the bendix or variator shaft splines: 1. Slack the belt by opening the CVT clutch gives belt slack to the variator side. 2. Then install the variator drive face while lifting the slack belt further away from the center boss if done properly should not see any splines between variator drive face and boss. Should be flushed together. 3. Then install existing variator fan, kick start gear, washer, and hand-tight nut. 4. Finally, torque nut to 30-35ft lbs. For reassurance please consult your manufacturer variator torque specs.

Specifications:

Include the following Drive face.

•    Aluminum CNC Machined Anodized Drive Face
•    Splines: 26 / I.D: 13mm<15mm / O.D: 113.7mm
•    Made in Taiwan
•    Fit Belt Size: 669, 729, 788
•    Fit QMB 49/50cc+

Supported Models: Naraku CVT Kit (Part# KIT.A.139QMB); GY6 139QMB 49cc-50cc engines, Buddy50, Filly 50, Kymco, QLink, SYM, TaoTao, and virtually any scooter engine with these measurements.

-----
Item Weight & Product Dimensions:
•    0.25 pounds | 4.476” (OD) x 0.512” (ID) x 0.5” (H)

Write a review

Note: HTML is not translated!
Bad Good
Captcha
Naraku Drive Face HS-CNC V.2 (139QMB)
  • Stock: 18
  • Brand: Naraku
  • Reward Points: 1
  • Model: NK900.59
  • Weight: 0.62lb
  • Dimensions: 6.50in x 6.00in x 2.25in
  • SKU: 137-29
  • MPN: NK900.59
Products Sold: 4
Product Views: 7478
$34.95
Price in reward points: 35

Included