Main Menu
Your Cart

NCY Clutch Spring 1500 RPM Set (DIO, GET, QMB)

NCY Clutch Spring 1500 RPM Set (DIO, GET, QMB)
NCY Clutch Spring 1500 RPM Set (DIO, GET, QMB)
NCY Clutch Spring 1500 RPM Set (DIO, GET, QMB)
NCY Clutch Spring 1500 RPM Set (DIO, GET, QMB)
NCY Clutch Spring 1500 RPM Set (DIO, GET, QMB)
NCY Clutch Spring 1500 RPM Set (DIO, GET, QMB)
NCY Clutch Spring 1500 RPM Set (DIO, GET, QMB)
NCY Clutch Spring 1500 RPM Set (DIO, GET, QMB)
NCY Clutch Spring 1500 RPM Set (DIO, GET, QMB)
NCY Clutch Spring 1500 RPM Set (DIO, GET, QMB)

Description: Clutch springs do a couple of things. First, they supply the pressure to engage the clutch. They also determine the rate at which the CVT transmission changes from low to high gear along assisting the compression spring. A 1000rpm clutch spring will go into a higher gear than a 1500rpm clutch spring. Color coated identifies the strength of the clutch spring, for example, a clutch spring color coated yellow is identified as 1500 RPM which will delay the clutch reaction by 1500 RPM. The greater RPM spring will provide you with greater power. NCY clutch pressure spring 1500 RPM uses a modified alloy spring providing better resilience and above-average strength for 139QMB, Buddy50, RoughHouse, and many other 49/50cc base engines.

Compatible with sport clutches on the market works on Honda Dio AF16 AF18E 50; Elite S/SE/SR 1994-2001, Daelim Cordi 50, Kymco Fever/ZX50, SYM DD50, GY6 40QMB 50cc 2-stroke, 139QMB 49cc-50cc 4-stroke, 50QMF 90cc-100cc, GY6 139QMB 49cc-50cc engines, Buddy50, Filly 50, Kymco, QLink, Peugeot, Piaggio, RoughHouse, SYM, TaoTao, Metropolitan GET 2012 & older, Honda Ruckus GET all U.S. Model, and virtually any scooter engine with these measurements.

NOTE: Will work on Metropolitan GET 2012 & older, Honda Ruckus GET all U.S. Model ONLY if you use WITH upgrade NCY Pulley Shaft, will NOT work with OEM pulley shaft.

Installation: Make sure variator drive face is seated properly and not get its teeth chewed by the Bendix: 1. Slack the belt by opening the CVT clutch gives belt slack to the variator side. 2. Then install the variator drive face while lifting the slack belt further away from the center boss if done properly should not see any splines between variator drive face slop-side and boss flat-side. Should be flushed together. 3. Then install the existing variator fan, washer, and hand-tight nut. 4. Finally, apply blue Loctitetorque nut to 30-35ft-lbs. For reassurance please consult your manufacturer's variator torque specs.

Specifications:

Include the following Clutch spring set.

•    3x Clutch Springs (yellow): 1500 RPM / L: 12.8mm / ID: 5mm / OD: 8.4mm
•    Hook-to-Hook L: 31.6mm / Wire OD: 1.6mm
•    Made in Taiwan
•    Fit Clutch Nut: M28 / Socket: 39mm
    Fit Clutch: 105mm / Shaft Slider: 33.5mm / Pins: 6mm / Nut: M10 / Washer: M10 / Bearing Seat47.4mm / Bell Spline: 22 Socket: 14mm
•    Fit Belt Size: 
660-18-28785-18-30 (Fit GET ONLY)
•    Fit Belt Size: 669729, 788-18-30 (Fit QMB ONLY)
•    Fit Belt Size: 654669-18-30 (Fit DIO ONLY)
•    Fit Compression Spring: 1k1.5k2k rpm
•    Fit Clutch Springs: 1k2k rpm
•    Fit Dowel Pin Set (8x10mm)
•    Fit DIO 49/90cc+
•    Fit GET 49/50cc
•    Fit QMB 49/50cc+

Supported Models: NCY CVT Kit (Part# 1200-1171); Honda Dio AF16 AF18E 50; Elite S/SE/SR 1994-2001, Daelim Cordi 50, Kymco Fever/ZX50, SYM DD50, GY6 40QMB 50cc 2-stroke, 139QMB 49cc-50cc 4-stroke, 50QMF 90cc-100cc, GY6 139QMB 49cc-50cc engines, Buddy50, Filly 50, Kymco, QLink, Peugeot, Piaggio, RoughHouse, SYM, TaoTao, Metropolitan GET 2012 & older, Honda Ruckus GET all U.S. Model, and virtually any scooter engine with these measurements.

-----
Item Weight & Product Dimensions:
•    0.0125 Pounds | 1.244" (L) x 0.33" (W) x 0.33" (H)

Write a review

Note: HTML is not translated!
Bad Good
Captcha
NCY Clutch Spring 1500 RPM Set (DIO, GET, QMB)
  • Stock: 40
  • Part #: 1200-1052-1.5K
Sold: 18
Views: 11880
$8.00
Price in reward points: 8

Included