Main Menu
Your Cart

NCY Secondary Sliding Sheave Shaft (Metro, Ruckus GET)

NCY Secondary Sliding Sheave Shaft (Metro, Ruckus GET)
NCY Secondary Sliding Sheave Shaft (Metro, Ruckus GET)
NCY Secondary Sliding Sheave Shaft (Metro, Ruckus GET)
NCY Secondary Sliding Sheave Shaft (Metro, Ruckus GET)
NCY Secondary Sliding Sheave Shaft (Metro, Ruckus GET)
NCY Secondary Sliding Sheave Shaft (Metro, Ruckus GET)
NCY Secondary Sliding Sheave Shaft (Metro, Ruckus GET)
NCY Secondary Sliding Sheave Shaft (Metro, Ruckus GET)
NCY Secondary Sliding Sheave Shaft (Metro, Ruckus GET)
NCY Secondary Sliding Sheave Shaft (Metro, Ruckus GET)
NCY Secondary Sliding Sheave Shaft (Metro, Ruckus GET)
NCY Secondary Sliding Sheave Shaft (Metro, Ruckus GET)

Description: NCY Secondary Sliding Sheave Shaft for Metropolitan, Honda Ruckus GET 49/50cc 4-stroke engines. This secondary sliding sheave shaft from NCY will give you quicker takeoff and higher top speed. Works well in conjunction with NCY Pin Set 6mm, Secondary Spring Seat/Funnel 43mm, and NCY Secondary Slider Plate 118.5mm (all sold separately). May also work with other brands as well.

NOTE: Recommend using a new belt with this kit. Belt and the belt drive-facing plates KEEP DRY. All, other areas apply moly-graphite grease when assembling. Example, lubricate slider grooves, slider pins, ball bearing seat, and inner funnel area with heat-resistant moly-graphite grease.

Installation: 1. Slack the belt by opening the CVT clutch gives belt slack to the variator side. 2. Then install the variator drive face while lifting the slack belt further away from the center boss if done properly should not see any splines between variator drive face slop-side and boss flat-side. Should be flushed together. 3. Then install the existing variator fan, washer, and hand-tight nut. 4. Finally, apply blue Loctitetorque nut to 30-35ft-lbs. For reassurance please consult your manufacturer's variator torque specs.

Specifications:

Includes the following Secondary slider (torque driver), Sliding sheave, Spring seat, O-rings, and clutch nut.

•    1x Rear Pulley Plate OD: 118.5mm / Shaft ID: 17.43<21mm / OD: 34<45.1mm / H: 68.73mm
•    1x Stainless Steel Clutch Nut: M28
•    Made in Taiwan
•    Fit Clutch Nut Socket: 39mm
    Fit Clutch: 105mm / Shaft Slider: 33.5mm / Nut: M10 / Washer: M10 / Bearing Seat47.4mm / Bell Spline: 22 Socket: 14mm
•    Fit Belt Size: 660-18-28 (Fit Metro ONLY)
•    Fit Belt Size: 785-18-30 (Fit Ruckus ONLY)
•    Fit Compression Spring: 1k1.5k2k rpm
•    Fit Clutch Springs: 1k1.5k2k rpm
•    Fit Dowel Pin Set (8x10mm)
•    Fit GET 49/50cc

Supported Models: NCY CVT Kit (Part# 1200-1220); Metropolitan GET 2012 & older, Honda Ruckus GET all U.S. Model, Zoomer 50cc, and virtually any scooter engine with these measurements.

-----
Item Weight & Product Dimensions:
•    0.968 pounds | 4.665" (OD) x 2.707" (ID) x 2.705 (H)

Write a review

Note: HTML is not translated!
Bad Good
Captcha
NCY Secondary Sliding Sheave Shaft (Metro, Ruckus GET)
  • Stock: 39
  • Reward Points: 2
  • Part #: 1200-1268-S
Sold: 2
Views: 1135
$69.00
Price in reward points: 69

Included