Main Menu
Your Cart

Prima Variator Roller Weight Tuning Kit 16x13 (DIO, GET, QMB)

Prima Variator Roller Weight Tuning Kit 16x13 (DIO, GET, QMB)
Prima Variator Roller Weight Tuning Kit 16x13 (DIO, GET, QMB)
Prima Variator Roller Weight Tuning Kit 16x13 (DIO, GET, QMB)
Prima Variator Roller Weight Tuning Kit 16x13 (DIO, GET, QMB)

tested on an actual gram scale tuning rollers can be offset by ± 0.1gm

Description: Prima Variator Roller Weight Tuning Kit 16x13mm test roller weight set for Honda DIO/Elite, GET, and 139QMB 4-stroke engines. 

For those of you unfamiliar with roller weights, they are an important tuning device and have a significant impact on your scooter's performance! They should be checked/changed every 1000 miles (per maintenance schedule) to keep your scooter running tops. Over time, roller weights will develop flat spots which will impair the performance of your scooter.

A good indication that your rollers are worn is increasingly high revs for a given speed and/or decreased top speed. Replacing worn rollers will restore and actually improve your low-end power and especially your top speed. Fuel efficiency will also improve dramatically!

Includes 36 Roller Weights, from 3gm to 14gm. Lighter roller weights will increase RPM for any given road speed. Heavier weights will lower RPM for any given road speed. Must be put in a 120° pattern!

NOTE: You must install these weights in an alternating pattern, otherwise a severe imbalance in the variator will occur. These rollers are designed for tuning purposes only and we recommend that they are not used for long-term use. Once you have determined the appropriate weight for your set up you should buy a complete roller set for permanent use.

Installation: Make sure variator drive face is seated properly and not get its teeth chewed by the Bendix: 1. Slack the belt by opening the CVT clutch gives belt slack to the variator side. 2. Then install the variator drive face while lifting the slack belt further away from the center boss if done properly should not see any splines between variator drive face slop-side and boss flat-side. Should be flushed together. 3. Then install the existing variator fan, washer, and hand-tight nut. 4. Finally, apply blue Loctitetorque nut to 30-35ft-lbs. For reassurance please consult your manufacturer's variator torque specs.

Specifications:

Include the following Roller weight set.

•    36x Roller Weights: 16x13mm 3gm<14gm
•    Made in Taiwan
•    Fit Variator Housing: 88mm89mm or 95mm Slides: 3 / Boss: 20mm / Shims: 20mm
    Fit Variator Shaft Nut: M12 / Washer: M12 / Socket: 17mm
•    Fit Belt Size: 654669-18-30 (Fit DIO ONLY)
•    Fit Belt Size: 660-18-28 (Fit Metro ONLY)
•    Fit Belt Size: 785-18-30 (Fit Ruckus ONLY)
•    Fit Belt Size: 669, 729, 788-18-30 (Fit QMB ONLY)
•    Fit Dowel Pin Set (8x10mm)
•    Fit DIO 49/90cc+
•    Fit GET 49/50cc
•    Fit QMB 49/50cc+

Supported Models: Naraku CVT Kit (Part# KIT.A.139QMB); Honda Dio AF16 AF18E 50; Elite S/SE/SR 1994-2001, Daelim Cordi 50, Kymco Fever/ZX50, SYM DD50, GY6 40QMB 50cc 2-stroke, 139QMB 49cc-50cc 4-stroke, 50QMF 90cc-100cc, GY6 139QMB 49cc-50cc engines, Buddy50, Filly50, Kymco, MetropolitanGET, QLink, Peugeot, Piaggio, RoughHouse, RuckusGET, SYM, TaoTao, and virtually any scooter engine with these measurements.

-----
Item Weight & Package Dimensions:
•    0.768 pounds | 9.5" (L) x 6" (W) x 0.575" (H)

Write a review

Note: HTML is not translated!
Bad Good
Captcha
Prima Variator Roller Weight Tuning Kit 16x13 (DIO, GET, QMB)
  • Stock: 37
  • Reward Points: 1
  • Part #: 1400-1069
Sold: 3
Views: 4447
$34.95
Price in reward points: 35

Included