Stage6 Variator Sport PRO 16mm Set (Aprilia, JOG, Zuma 50)
Description: Stage6 Variator Sport PRO 16mm Set for Aprilia, JOG, Zuma 50, and many other 50cc base engines. With their new SportPRO variator kit, Stage6 again introduce a state-of-the-art tuning part into their product range. The variator comes adjusted for use with a 50cc cylinder and a Stage6 ProReplica exhaust system. It has been developed and optimized for use with Stage6 SportPro/ Street race or similar 70cc sport cylinders though. The back of the variator and the roller tracks are hard coated, the running surface is, however, uncoated. On the one hand, this reduces the running surface's lifespan, on the other hand, the increased friction coefficients result in better performance. Furthermore, the coating cannot flake off, as it may happen with hard-coated running surfaces, which would lead to quicker wear or even breaking of the drive belt. Included in this kit is the variator with two different bushings (for 13 and for 16mm variator shafts), two back plates with low-friction coating, shims, a set of roller weights (16x13), and a torque spring.
Installation: Make sure variator drive face is seated properly and not get its teeth chewed by the Bendix: 1. Slack the belt by opening the CVT clutch gives belt slack to the variator side. 2. Then install the variator drive face while lifting the slack belt further away from the center boss if done properly should not see any splines between variator drive face slop-side and boss flat-side. Should be flushed together. 3. Then install the existing variator fan, washer, and hand-tight nut. 4. Finally, apply blue Loctite, torque nut to 30-35ft-lbs. For reassurance please consult your manufacturer's variator torque specs.
Specifications:
Includes the following Variator, Variator bosses, Variator shims, Variator slides, and Variator tops .
2. Includes Stage6 Variator, Roller weights, Variator bosses, Variator housing, Variator shims, variator slides, and Variator top.
• 1x Alumin-Alloy Housing ID: 19.95mm / OD: 95.95mm / H: 27.42mm / W: 167.26gm
• 2x Stainless Steel Bosses L: 37.5mm / ID: 13<16mm / OD: 20mm
• 2x Stainless Steel Shims L: 1mm / ID: 13<16mm / OD: 20mm
• 2x Metal Tops ID: 13<16mm / OD: 71<73mm / H: 14.25mm
• 6x Black Roller Weights: 16x13mm 5gm
• 3x Plastic Slides (white)
3. Include Stage6 Compression Spring
• 1x Spring Comp: (black) Stiffer Than Stock / L: 116.7mm
• Spring ID: 46.7mm / OD: 54mm
• Wire Gauge: 3.6mm
• Made in Italy
• Fit Aprilia 50
• Fit JOG 50
• Fit Zuma 50
Supported Models: Aprilia Amico 50, Aprilia Area 51, Aprilia Gulliver 50 AC, Aprilia Rally 50 AC, Aprilia SR 50 AC, Aprilia Scarabeo 50, Aprilia Sonic 50 AC, Benelli 491 GT 50, Benelli 491 RR 50, Benelli 491 ST 50, Benelli 491 Sport 50, Benelli K2 50, Benelli Naked 50, Benelli Pepe 50, Beta Ark 50 AC, Beta Ark 50 LC, Beta Chrono 50, Beta Eikon 50, Beta Quadra 50, Beta Tempo 50, Buffalo Fox 50, Buffalo Rex 50, Buffalo Wind 50, CPI, Italjet Dragster 50, KTM Ark 50, Keeway, Kreidler Florett 50, MBK Booster 50, MBK Flipper 50, F10 50 Jetline, Malaguti F12 Phantom 50 AC, Motobi Pesaro 50, Motowell Magnet RS 50, Rex (Jinan Qingqi) Escape 50, Streak Access 50, Vento, Yamaha Aerox 50, Yamaha BWS 50, Yamaha Jog 50, Yamaha Zuma 50, and virtually any other scooter engine with these measurements.
-----
Item Weight & Package Dimensions:
• 0.581 pounds | 7.7" (L) x 6.25" (W) x 2.9" (H)