NCY CVT KIT Gen 4 Plus (GY6)
Description: NCY CVT Kit Gen 4 Plus GY6 aka Super CVT transmission kit for GY6 125/150cc+ engines is one of the best dollar-for-dollar bolt-on to improve your GY6 125/150cc+ or Polaris RZR 170! Quicker acceleration, reach faster top speeds, and makes your GY6 CVT the smoothest running transmission in town! From rapid downshifting to slow cruising, this thing is smooth. Ultralight balanced components, oversized wear pads, and state-of-the-art polytetrafluoroethylene (PTFE) coatings ensure superior performance and long service life.
NOTE: THIS KIT IS NOT FOR Honda PCX (See Part# 1200-1195). Must re-use stock variator boss, washers, rear pulley plate shaft, slider pins, slider seat funnel cover, clutch nut, and nuts. For some models like the Polaris RZR 170, you'll need to widen the NCY Variator Top plate center hole, with a dremel tool, to fit through its variator shaft. Recommend using a new belt with this kit. Belt and the belt drive-facing plates KEEP DRY. All, other areas apply moly-graphite grease when assembling. Example, lubricate slider grooves, slider pins, ball bearing seat, and inner funnel area with heat-resistant moly-graphite grease.
Installation: 1. Slack the belt by opening the CVT clutch gives belt slack to the variator side. 2. Then install the variator drive face while lifting the slack belt further away from the center boss if done properly should not see any splines between variator drive face slop-side and boss flat-side. Should be flushed together. 3. Then install the existing variator fan, washer, and hand-tight nut. 4. Finally, apply blue Loctite, torque nut to 30-35ft-lbs. For reassurance please consult your manufacturer's variator torque specs.
100% NCY Products – OPTIONAL ADD-ON (IN RED)
Includes the following Drive face, Roller weights, Variator, Secondary slider, Springs, Spring bearing seat, Clutch, and Clutch bell.
1. Include NCY Drive Face, Drive Face CNC-Machined.
• 1x Aluminum CNC Machined Anodized Drive Face Weight: 144.7gm
• Splines: 19 / ID: 13.5mm / OD: 114mm / H: 10<13.55mm
2. Includes NCY Variator 115mm Coated Gold, Roller weights, Variator housing, Variator slides, and Variator top.
• 1x Alumin-Alloy Housing Teflon Coated ID: 24mm / OD: 115mm / H: 36mm
• 1x Metal Top ID: 15mm / OD: 87mm / H: 24mm
• 6x Roller Weights (red): 18x14mm 10gm
• 6x Roller Weights (red): 18x14mm 11gm
• 6x Roller Weights (red): 18x14mm 12gm
• 3x Plastic Slides (red)
3. Includes NCY Secondary Slider, slider (torque driver), and O-rings. (Make Selection)
• 1x Secondary Slider Plate OD: 141.84mm / Funnel ID: 34mm / OD: 43mm / H: 47mm
• 2x Rubber O-rings (pre-installed)
4. Includes NCY Secondary Bearing Spring Seat, Bearings, and Bearing seat.
• 1x Bearing Seat ID: 45.4mm / OD: 57.5mm / H: 3mm / Grove: 1.75mm
• 1x Bearings Pak
5. Include NCY Compression Spring, Compression spring. (Make Selection)
• 1x Spring Comp (yellow): 1,500 RPM / L: 154mm
• Spring ID: 48.5mm / OD: 58.2mm
• Wire Gauge: 4.2mm
6. Includes NCY Clutch Gen 4 Performance Green, Clutch housing, Clutch springs, and Clutch weights.
• 1x Clutch ID: 24.3<28mm / OD: 121.8mm / H: 36.85mm
• 3x Clutch Spring (red): 2000 RPM (Make Selection)
• 3x Clutch Weights (green)
7. Include NCY Clutch Bell, Clutch Bell PTFE Coated.
• 1x Iron Clutch Bell (10-Spokes) Weight: 680.39gm / ID: 125mm / OD: 137.34mm / H: 43mm
• Splines: 19 / ID: 13.5<15mm / OD: 20mm / H: 24.77mm
• Made in Taiwan
• Fit Variator Boss: 24mm / Shims: 24mm / Nut: M12 / Washer: M12
• Fit Clutch Shaft: 174mm / Sheave: 34mm / Nuts: M12, M28 / Washer: M12 / Bearing Funnel: 43mm / Socket: 17mm, 39mm
• Fit Compression Spring: 1k, 1.5k, 2k rpm
• Fit Clutch Springs: 1k, 1.5k, 2k rpm
• Fit Belt Size: 743, 835, 842-20-30
• Fit Dowel Pin Set (8x10mm)
• Fit GY6 125/150cc+
Supported Models: NCY CVT KIT - CUSTOMIZABLE (Part# 1200-1252); GY6 152QMI 157QMJ 161QMK 161QML Chinese Scooter, ATV, Genuine Buddy, Kymco, Polaris RZR 170, Ruckus GY6 Swap, Vento
Item Weight & Package Dimensions:
• 6.731 pounds | 17.5” (L) x 6.45” (W) x 5” (H)